ALTAIR RS-485 PORT WINDOWS 8 DRIVER DOWNLOAD


Download Now
Altair RS-485 Port Driver

Additional remote sensors can be attached to the unit via the RS network port, while a mA output is proportional to the calibrated operating range. signal into digital or analog signal output(mA analog signal,RS communication signal and switch quantity alarm signal to transmit remotely and drive). Proprietary RS remote controls can be daisy chained in different areas along While the USB port allows easy and quick setup or changes, the Ethernet.


ALTAIR RS-485 PORT DRIVERS FOR WINDOWS MAC

Type: Driver
Rating:
4.95
435 (4.95)
Downloads: 944
File Size: 22.80Mb
Supported systems: Windows 2008, Windows XP, Windows Vista, Windows 7/8/10
Price: Free* [*Free Registration Required]

Download Now
Altair RS-485 Port Driver

Compatible Ready-to-use Hardware

Modular connectors were developed for use on Altair RS-485 Port Bell System telephone sets in the s, similar types found use for simple interconnection of customer-provided telephone subscriber premises equipment to the telephone network; the Federal Communication Commission mandated in an interface registration system, Altair RS-485 Port which they became known as registered jacks.

The convenience of prior existence for designers and ease of use led to proliferation of modular connectors for many other applications. Many applications that used a bulkier, more expensive connector have converted to modular connectors; the best known applications of modular connectors are for telephone and Ethernet.

Accordingly, various electronic interface specifications exist for applications using modular connectors, which prescribe physical characteristics and assign electrical signals to their contacts. Modular connectors are referred to as modular phone jack and plug, RJ connector, Western jack and plug.

DRIVERS FOR ALTAIR RS-485 PORT

The term modular connector arose from its original use in a novel system of cabling designed to make telephone equipment more modular; this includes 4P4C used for handset connectors. Registered jack designations describe the signals and wiring used for voice and data communication in modular and other connectors, it is common to use a registered jack number to refer to the physical connector itself.

Altair RS-485 Port common use of 8P8C connectors is Ethernet over twisted pair ; the 4P4C connector is sometimes erroneously called RJ9 or RJ22 and various six-position modular connectors may be incorrectly called RJ Driven by demand for multiple sets in residences with various lengths of Altair RS-485 Port, the Bell System introduced customer-connectable part kits and telephones, sold through PhoneCenter stores in the early s.

Altair's New Personal PBS(TM) Turns Personal Computers into Powerful Compute Clusters for Free

For this purpose, Illinois Bell started installing modular telephone sets on a limited scale in June The patents by Edwin C. Hardesty and coworkers, US and USfollowed by other improvements, were the basis for the modular molded-plastic connectors that became commonplace for telephone cords by the s. Inthese connectors were standardized nationally in the United States by the Registration Interface program of the Federal Communication Altair RS-485 Port, which designated a series of Registered Jack specifications for interconnection of customer-premises equipment to the public switched telephone network.

Modular connectors have gender: Plugs are used to terminate cables and cords, while jacks are used for fixed locations on surfaces of walls and equipment. Other than telephone extension cables, cables with a modular plug on one Altair RS-485 Port and a jack on the other are rare. Instead, cables are connected using a female-to-female adapter, having two jacks wired back-to-back.

RS Port (COM3) Download Driver

Modular connectors are designed to latch together. As a plug is inserted into a jack, a plastic tab on the plug locks so that the plug cannot be pulled out.

To remove the plug, the latching tab must be depressed against the plug to clear the locking edge; the standard orientation for installing a jack in a wall or panel is with the tab down. The latching tab may snag on other cables and break off resulting in Altair RS-485 Port of the secure latching feature. To prevent this, tabs are protected with a boot over the plug, or a special tab design, on snagless cords.

Most protective boots must be installed onto a cable; this means. However, protective boots or Altair RS-485 Port protective ramp adapters are available which can be snapped over an installed unprotected modular plug. Modular connectors are designated using two numbers that represent the maximum number of contact positions and number of installed contacts, with each number followed Altair RS-485 Port P and C, respectively.

For example, 6P2C is a connector having two installed contacts. Alternate designations omit Altair RS-485 Port letters while separating the position and contact quantities with either an x or a slash. When not installed, contacts are omitted from the outer positions inward, such that the number of contacts is always even; the connector body positions with omitted or unconnected contacts are unused for the electrical connection, but ensure that the plug Altair RS-485 Port correctly.

DRIVERS: ALTAIR RS-485 PORT

For instance, RJ11 cables have connectors with six positions and four contacts, to which are attached just two wires; the contact positions are numbered sequentially starting Altair RS-485 Port 1. When viewed head-on with the retention mechanism on the bottom, jacks will have contact position number 1 on the left and plugs will have it on the Altair RS-485 Port. Contacts are numbered by the contact position.

For example, on a six-position, two-contact plug, where the outermost four positions do not have contacts, the innermost two contacts are numbered 3 and 4. Modular connectors are manufactured in four sizes, with 4- 6- 8- positions. The Altair RS-485 Port plastic bodies of 4P and 6P connectors have different widths, whereas 8P or 10P connectors share an larger Altair RS-485 Port width. Internally, the contacts on the plugs have sharp prongs that, when crimped, pierc.

Related Posts